# $Id: config.ttyS0,v 1.1.1.1 2002/08/14 22:28:15 dan Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		34
AreaCode:		942
FAXNumber:		+34942xxxxxx
LongDistancePrefix:	00
InternationalPrefix:	""
DialStringRules:	etc/dialrules.europe
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0644
LogFileMode:		0600
DeviceMode:		0660
# Si RingsBeforeAnswer = 0 se desactiva la recepción en este modem
RingsBeforeAnswer:	1
SpeakerVolume:		medium
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Solvay Torrelavega"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.0	# use this to supply a hint
ModemRate:		38400		# max rate for DCE-DTE communication
ModemFlowControl:	rtscts		# XON/XOFF flow control assumed
ModemSetupDTRCmd:	ATS13=1&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:		ATDT%s		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:		""		# stuff to do when modem is reset
ModemAnswerCmd:		ATA		# use this to answer phone
ModemNoFlowCmd:		AT&H0&I0&R1		# disable flow control cmd
ModemHardFlowCmd:	AT&H1&I0&R2		# hardware flow control cmd
ModemSoftFlowCmd:	AT&H2&I2&R1		# software flow control cmd
ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:	ATE0		# disable command echo
ModemVerboseResultsCmd:	ATV1		# enable verbose command results
ModemResultCodesCmd:	ATQ0X4		# enable result codes
ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
ModemSoftResetCmd:	ATZ		# do soft reset of modem
ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:		AT+FCLASS=2.0	# command to enter class 2.0
Class2BORCmd:		AT+FBO=0	# bit order for phase B/C/D (direct)
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FKS		# abort session command
# Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2CQQueryCmd:	!(0),(0)	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FPP=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBU=0
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities command
Class2DISCmd:		AT+FIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FPI		# set polling identifier command
Class2NRCmd:		AT+FNR=1,1,1,0
# Class2PIECmd:		AT+FIE=0	# disable interrupt-enable command
Class2PIECmd:		""		# disable interrupt-enable command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=0	# set no flow control command
Class2SFLOCmd:		AT+FLO=1	# set software flow control command
Class2HFLOCmd:		AT+FLO=2	# set hardware flow control command